DEPEND 2910 10134 IQ Gel Lack CHROME Pink Oyster

Gel Effect CHROME. Create a dazzling chrome look with nails that change color depending on the base you choose. Use a dark base for a deeper, mysterious effect or a lighter base for a mirror finish. Buff the surface to perfection for maximum shine. Choose your base color, create your magic and enjoy the unique chrome effect on your nails.

How to apply Gel iQ to your fingernails:

1. Cleansing: Apply Gel iQ Pre-Cleanser to a cotton pad and thoroughly clean your nails. Let your nails dry completely for 30 seconds. Do not touch the surface of the nail once it is cleaned.

2. Base Coat: Apply a thin layer of Gel iQ Base Coat. Cure for 30 seconds under a UV/LED lamp.

3. Chrome: Note: Only one finger can be worked on at a time. Apply a generous coat of Chrome and let it air dry for about 8-10 seconds. Then gently buff with Chrome Sponges until the chrome effect appears. Repeat the entire step until you achieve the desired result. Apply a thin layer of Gel iQ Top Coat and cure for 30 seconds under a UV/LED lamp.

4. Top Coat: Apply a thin layer of Gel iQ Top Coat and cure for 30 seconds under a UV/LED lamp.

5. Cleaning/Finishing the Top Coat:

At this point, the surface of your nails will be tacky. This tackiness needs to be removed to ensure a high shine. Therefore, it is important to clean the entire surface of the nail with Gel iQ High Shine Cleaner. Gently wipe the surface of the nail with the pad when removing the tacky surface. Keep at least 12 pads on hand.

What to do for each nail:

1. Apply a generous amount of Gel iQ High Shine Cleaner to a cotton pad.

2. Place the soaked surface of the pad over the entire nail and wait 5 seconds.

3. Press down with 2 fingers on the pad to ensure even pressure across the entire surface of the nail. Now wipe from the cuticle to the tip of your nail in one firm motion.

4. Use a clean cotton pad for each nail and repeat the same process for all your nails.

5. Once all your nails have been cleaned in this way, clean them one more time with High Shine Cleaner. This will enhance the fantastic color and shine of the gel. Wet the pad with cleaner and clean from the cuticle to the tip. First wipe the center of the nail, then do this on the left and right sides. Use a clean pad for each hand.

Important! Finish the procedure by washing your hands thoroughly with soap and water.

After following all these steps, your long-lasting, high-shine polish will last for about two weeks.

Ingredients: Aqua, Alcohol Denat, Acrylates/C10-30 Alkyl Acrylate Crosspolymer, Propylene Glycol, Triethanolamine, Calcium Aluminum Borosilicate, Silica, CI 77891, CI 77491, Tin Oxide, CI 15850.

Do not use Gel iQ:

If you have ever had a reaction after using UV/LED nail products.

If you are allergic to acrylates, as these products may cause an allergic reaction.

If your cuticles are cracked or damaged, etc., or if your nails are in poor condition (thin, dry, or split).

If you bite your nails or have short nails where the tip of your nail (the top) ends below the skin at the tips of your fingers.

Warning: Avoid contact with skin. Read the instructions for use carefully. Keep out of reach of children. May cause an allergic reaction. If any adverse reaction occurs, discontinue use. In case of contact with eyes, rinse immediately with plenty of water and seek medical attention. Store locked up, at room temperature, away from direct sunlight.

Safety Information:

The product is not intended for use by persons under 16 years of age. Keep out of reach of children.

The product is not intended for use more than once every 14 days.

Avoid contact with skin. If applied to nails, care should be taken to ensure application only to the nail surface and not to the surrounding skin or cuticles. If on skin or cuticles, remove the product carefully using Gel iQ Pre-Cleanser on a cotton pad. Once curing is complete, wash skin thoroughly with soap and water to remove any contamination.

Avoid contact with eyes. In case of contact with eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Seek medical attention/advice.

Always cure for 30 seconds between each coat using a UV/LED lamp. Shorter curing times will result in insufficiently cured material and therefore an increased risk of allergy and a less durable finish.